How do we pay for hot water? How to pay for housing and communal services with and without meters. What do we pay for

18.06.2021

Almost all housing conditions nowadays are equipped with water supply systems. However, not every apartment has a meter for cold and hot water supply. IN similar situations The water tariff is calculated monthly depending on the number of people living in the house.

Therefore, if you count without control readings, the bills for drainage will have exorbitant amounts. We suggest that you quickly install a metering device so that payments are made correctly and without additional charges to the water meter according to the consumption of the number of liters of liquid.

To calculate the water supply correctly, it is necessary to take the readings indicated on the dial of the device. This will help clarify the exact use of liters in the allotted period. We recommend using a calculator to get accurate values.

Each device has an individual design, so each unit will differ in color and number arrangement. This principle is typical for both hot pipelines and cold water. In order to easily read the values, the water meter must be in an accessible place.

It should be noted that the readings located at the end are used for measurement. Let's say your water meter shows 000408, without paying attention to the numbers that are constantly rotating, we determine that we have used 408 cubic meters of liquid. Preliminary numbers (zeros) are intended for further readings, counted liters

How to calculate water charges

Let's perform calculations using the example of the Crimean tariff for water supply and sanitation, which then need to be paid. Also, by analyzing all the data, you can find out for yourself how many liters of cold liquid were consumed. The main thing is to correctly take the values, the unit of measurement of which is considered to be a cubic meter.

In order to calculate hot or cold supplies, you will need the existing water supply tariff and meter readings. According to our data, the water meter reading is 408 units per cube, the current tariff for water supply and sewerage is 17 rubles. 63 kopecks

Now we look in the payment account book for the previous water meter readings of 403 cubic meters. From the larger value we subtract the smaller one, that is, 408 units per cubic meter - 403 cubic meters = 5 cubic meters. m. We multiply the resulting difference by the tariff: 5 * 17.63 = 90 rubles. for only 5 units per cube. You can use a calculator for the procedure.

Note! The calculation of water supply and sewerage services is carried out jointly, so the tariff will seem high, regardless of the liters consumed. Every six months you will have to calculate expenses according to new tariffs.

After completing all the required calculations in the cube, we take the water payment book and go to the nearest bank where utility bills are accepted in order to pay for the services. You can also make payments via terminals and the Internet. We advise you to note that the tariff for supplying hot and cold water changes once every year or six months, so it is recommended to periodically familiarize yourself with the price of water.

Excerpt from legislation or how to pay for water by meter

Let's consider how many nuances there are when calculating the liters by which you can pay for drinking liquid in an apartment or private house. To date, these data have already been approved, but are quite far from ideal. Therefore, in different regions, such a calculation may vary in amount.

Basically, the amount we receive in the receipt is measured from the following terms:

For an apartment with cold water, you often have to pay for hot liquid suitable for drinking and separately for bathing, which can be labor-intensive to calculate on your own. Here, payment is made for two services at the same time: when providing water supply and sanitation.

When paying incoming bills, it is recommended to save all receipts and stubs. Since if inspectors come to take readings, they have the right to demand payment receipts. A visit log must also be provided, where you will put your signature.

General building meters can be installed in entrances; when calculating the amount of cost, it is divided among all residents.

ODN: duty or whim of utility workers?

Citizens, tenants and owners of living space must pay utility bills monthly, so payments should be made regularly. The slightest delay costs a penalty for the service. Often you can find additional payment figures in the stubs.

It is noted that one must be paid by residents when living in an apartment building and using common building services. Payment for one is specified in the Federal Law, which provides for the provision of water supply and sanitation services in multi-apartment residential buildings. To date, there is no compliance with the standards of liquid intended for public needs, how many liters should be used.

When providing communications for household and other needs, the organization must be guided by a special formula to determine the calculation for one. Often, payment for such a service is calculated for each residential area individually. This will also be affected by whether the house has a water meter.

It is necessary to take the correct readings as shown by the general building meter and subtract the volume that was consumed by non-residential apartments, apartments that calculate payment according to the standard and premises that have an installed meter.
The number of cubic meters that was obtained for use for general house needs is multiplied by the area of a certain apartment and divided by the area that constitutes all residential and non-residential premises in an apartment building. Such conditions are also established for hot water if it is supplied to the house.

Standard consumption for each individual region is approved by the regional administration and government. The price is set depending on hot and other types of collateral. Ultimately, the receipt indicates the tariff at which everything needs to be calculated.

What exactly do you have to pay for?

Now the requirement to pay for general house needs often causes confusion among residents. In this section we will try to figure out what the calculation for the service one for hot and cold water supply is. If this requirement is not met, housing and communal services workers have the right to remove the meter and seal the pipeline.

In the matter of providing water, a similar combination of letters refers to such general house needs as washing floors and stairwells between floors, washing courtyards and windows. Watering front gardens in the courtyard area and caring for lawns is also included in the water supply tariff for one person.

For example, residents of an apartment building decided to independently clean the territory, water the land, monitor the condition of the entrances, and also fulfill other needs. They should first be calculated. For all this, a certain consumption of liquid (possibly a certain number of hot liters) is used for general house needs. There is a certain standard for how many cubes there should be.

Typically, for one, a separate water intake valve is used, on which a liquid metering and control meter is installed, on which the entire expended volume is recorded, and as a result, a calculation is carried out.

Is it possible to reduce water consumption and payment for one?

The method of correctly saving water for general household needs always exists, but each individual case has its own rules and principles, regardless of what the tariff for the service will be. As for one, then you can follow these recommendations:

when living in an apartment building where cold water is used, try to insist that each apartment owner has a water meter; it is also necessary to require companies providing water supply services and shared sanitation, if necessary, to take readings for convenience, and it will become easier to pay;
submit readings from general and individual water meters to the relevant authority on time. To do this, it is enough to record the readings correctly in a special paybook;
control the work of plumbing in the house. This will help control excess costs and water needs.

Attention! When performing calculations, before paying for common house needs, you must indicate the exact number of people living in the apartment building and take the readings correctly. The average statistical tariff is also charged for this number, especially in cases where many apartments do not have a water meter installed and they use more than just cold water. Checking water meters without removing them: stages of the procedure... A comfortable home usually includes utilities such as water supply. And for its economical use, water meters are installed. So...

For drinking and cooking (dehydration of the human body must not be allowed, as this leads to death).
In agriculture (for the growth of crops: vegetables, fruits, berries, etc.).
As a solvent (most often in industrial applications).
As a coolant (hot - in heating networks for heating premises, cold (ice) - for cooling in the catering industry and in medicine).
When extinguishing fires and fires (both in liquid form and in the form of foam).
As a tool (for example, for waterjet cutting).
As a lubricant (in emulsion lubricants).

Calculation of fees for hot water supply

Hot water supply- supply of hot water supplied through centralized hot water supply networks and intra-house engineering systems in a residential building (household), in residential and non-residential premises in an apartment building, as well as in premises that are part of the common property in an apartment building.

Explanations on payment for hot water in 2012 (Register of payments for January-February 2012)

Tariffs from January 2011 to June 2012 were approved by REC TO in the following amounts: for heat energy per 1 Gcal: 615.52 rubles excluding VAT (Orders No. 696-np dated November 29, 2010 and No. 255-np dated October 29, 2010), for water disposal - 16.83 rubles, for cold water - 11.54 rubles with VAT per 1 m3 (Orders No. 687-np and 688-np dated November 29, 2010), for coolant - 13.81 rubles per 1 m3 and are unchanged until their changes by the authorized body. The indicated tariffs for thermal energy and coolant are components of the tariff for 1m3

How to correctly calculate the payment for hot water

Residents of apartment buildings usually do not directly pay for one. Since this is the responsibility of the local housing department or homeowners association, for them there is a special line in the payment receipt with this indicator, which will need to be paid as part of the general receipt. If the amount in your opinion is too high, this may be the reason for your request to recalculate it. This must be done by the management company within ten days. If this does not happen, you have the right to appeal the company’s actions to the Housing Inspectorate or court.

Cost of Gcal of heat and cubic meter of hot water according to the meter

At a thermal power plant, water is converted into steam, the steam turns the turbine, converting the kinetic energy of the steam into electricity, condenses again turning into water, and it is this water that is used for heating. Respectively water and heat in water for thermal power plants, it is a by-product, or, more simply, waste.

How to count water using meters and using what methods

Today, in almost every apartment you can find such a device as a water meter. Using a water meter, the owner can keep track of the amount of water consumed, which allows him to save a lot on paying for it. However, not every owner, after installation, has an idea of how to calculate the amount to be paid for consumed water. The calculation method itself is quite simple, so you don’t need any specific knowledge to understand this process. Something else is more important. Over time, certain water meter models may show incorrect data, which can result in extremely large savings or increased water bills.

Payment for hot water

By Decree of the Government of the Russian Federation No. 344 of April 16, 2013. Amendments have been made to the Rules for the provision of public utility services, approved by Decree of the Government of the Russian Federation No. 354 of 05/06/2011, namely, the distributed volume of general house needs should not exceed the volume calculated on the basis of consumption standards for public services provided for general house needs.

Payment for hot water

It is clear that floorboards do not radiate heat. Heat is emitted by a source - battery sections, in an amount proportional to their area and temperature. CMOR is a const value under any circumstances and allows unreasonable charges to be collected even with cold batteries. Abusing the trust of Russian citizens, these circumstances are used for selfish purposes by unscrupulous and immoral officials of various ranks and “new businessmen”. The amount of losses from family budgets compatriots in annual terms only according to our MKD are hundreds of thousands of rubles, and in Russia - billions.

Payment for hot water using new electronic meters

to drawa: Thank you for your attention to my question. But in your advice, firstly, there is an inaccuracy: the “sewers” also have their own website http://www.hkov.kharkov.ua/, and secondly, the question is not to transfer the readings to the megabank or to the supplier services, but to NOT PAY TWICE to such organizations as KP TP VODA and Kharkovkommunochistvod.
Moral of the story: if in the readings for cold water I have already summed up what passed through the cold and hot pipes, then why should I pay again for the water heating usage indicator generated by the meter, according to the coefficients. I won't!

The provision of utility services is regulated by the Housing Code of the Russian Federation, in particular Federal Law No. 210 of December 30, 2004 “On the basis for regulating tariffs of public utility organizations.”

Rules for the provision of public services to citizens have been approved Decree of the Government of the Russian Federation No. 307 of May 23, 2006. In 2017-2018, there was some change in the approved ones; the tariffs for hot and cold water changed. In 2019, tariffs increased in almost all regions of Russia.

Who sets the rates?

And water supply, including, turns out to be resource supply organizations on the basis of agreements concluded with consumers.

According to Article 157 Part 2 of the Housing Code of the Russian Federation, payment for water is calculated according to approved tariffs. Tariffs are set by state authorities of the constituent entities of the Russian Federation and local self-government bodies in the manner prescribed by law.

Article 3, clause 3 of Federal Law No. 210 states that the final amount of payment for water supply services is established taking into account the approved tariff and its premium for the provision of the service.

That is, the water tariff is set by local governments based on current tariffs and the necessary allowances in accordance with the maximum indices in force in the given territory.

Limit indices established by government bodies of the constituent entities of the Russian Federation determine the maximum and minimum limits for changing tariffs, taking into account surcharges.

Thus, the resource supplying organization must calculate the costs associated with water supply. According to this indicator and the approved tariff, government agencies determine the final cost for the consumer.

Wherein the organization's ownership of the well does not matter, the supplier organization does not have the right to set a price higher than the maximum permissible value.

How is the fee calculated and what is included in the cost of a cubic meter of water?

By paying for the supply of hot and cold water, the consumer pays not only for the water itself, but also for organizing its submission. So the price of water includes:

All costs are considered strictly in accordance with statutory standards.

Difference in tariffs with and without a meter

There is no difference in tariffs with and without a meter and there shouldn’t be. A cubic meter of water costs the same in any case, another thing is that payment for water is calculated differently.

So, when using water without a meter, the main indicator is taken “water norm” per person.

This amount is multiplied by the number of citizens living in the apartment, after which the total amount is calculated according to the current tariff.

If there is a water meter, the actual amount of resource consumed is calculated, regardless of the number of registered residents.

But in this case, you will also need to pay, which is distributed to all owners of individual metering devices in accordance with the volume of water they used.

Since June 2011, the decision of the Government of the Russian Federation No. 354 of May 6, 2011 “On the provision of utility services to owners and users of premises in apartment buildings and residential buildings” has been in force.

Based on this, the presence of an individual water meter in a single apartment is in no way does not eliminate the need to pay for general house overuse of water resources.

But since many multi-apartment residential buildings, if available, have both residential premises equipped with individual metering devices and premises without them, many consumers do not understand how payment for water is calculated taking into account the general overexpenditure of the resource.

Decree of the Government of the Russian Federation No. 307 of May 23, 2006 defines the formula by which payment for the provided resource is calculated when taking into account the readings of a common house water meter.

To calculate payment, the following steps are carried out:

To pay for overruns once a year the management company adjusts payments, that is, the above formula applies. As a result, an additional amount to be paid appears in the receipts of apartment owners with meters.

Overconsumption of water usually occurs due to:

excessive waste of water in premises without a meter;
water losses due to faulty condition of intra-house networks;
uncoordinated connection of individual consumers to intra-house networks, for example, for watering green areas and plantings near the house;
non-accounting in the payment system for citizens not officially registered, etc.

Thus, the difference between the readings of the common house meter and the actual water consumption is paid by the owners of individual meters.

In this case, installing water meters may become unprofitable, and therefore a law was passed obliging all consumers to install water meters.

According to the Decree of the Government of the Russian Federation No. 354, all property owners had to install water meters before July 1, 2013.

In the absence of a meter, from January 1, 2015, payment for water was calculated by adding 10% to the existing tariff, from July 1, 2015, 20% was added to the tariff, then the amount of the additional payment was increased and adjusted, reaching 50% by January 1, 2019.

Also, the Russian Government was developing a project that was supposed to determine social norm for water consumption. If this indicator is exceeded, then payment is made at an increased rate.

Current consumption standards for hot and cold water

Tariffs for hot and cold water for the population are regulated by the state, that is, determined by regional authorities in accordance with the methodology approved by the Federal Tariff Service.

Wherein in different regions these rates can vary significantly, depending on the cost of organizing water supply.

Water tariff increase in 2019

According to representatives Russian government, the current socio-economic situation in the country forces enterprises involved in the supply of cold and hot water to the population to take measures to increase their tariff schedule.

At the same time, it is worth noting that such an increase in the cost of water supply at the level of 4.9, 4.4 and 4.1 percent is noticeably lower than the previously proposed growth rates of 6.2, 6 and 4.7 percent.

According to experts, there is simply no other way out of the current situation other than increasing the cost of tariffs, even though the burden on the country’s population is already quite serious. About 20 percent of our citizens are completely convinced that payments for water supply should not be collected. Of course, everything around us is becoming more expensive, there is an increase in basic energy resources, so an increase in water tariffs is a completely justified and justified measure.

It should also be noted that even such an increase in tariffs will not cover the need to modernize and repair the existing water supply network.

In 2019, an increasing factor of 1.5 (or 50% of the standard) is applied to utility services for hot water supply, hot water supply and electricity supply. For 2019, the figure has not changed.

This norm applies only to those citizens who do not have in their apartment recording the consumption of electricity, cold and hot water.

For consumers who do not have technical feasibility installation of metering devices, which is confirmed by a special act, nothing changes - they pay for consumption based on basic consumption standards, without increasing factors.

The main question that consumers of hot water and cold water services are now asking is: how to avoid increasing payments? It's simple: If it is technically possible to install individual meters, the consumer of utilities is obliged to install them, the same applies to a common house meter. In this case, the payer exempt from the application of a multiplying factor, since the calculation is made not according to the standard, but according to actual meter readings.

How to get rid of unnecessary payments?

Fees for " Maintenance water meters" - what is it? Is this legal and is it possible to refuse incomprehensible payments?

Many people, when paying for utility services, are surprised to see the phrase “water heating” on the receipt. In fact, this innovation was adopted back in 2013. According to Government Decree No. 406, if there is a centralized water supply system, payment must be made at a two-component tariff.

Thus, the tariff was divided into two components: the use of cold water and thermal energy. Now the calculation is made separately for two resources: water for hot water supply and thermal energy. That is why a column appeared on receipts indicating the amount of thermal energy spent on heating cold water. However, many believe that heating fees are charged illegally and write complaints to housing and communal services. To ensure the legality of this type of charge, you should learn more about this service.

The reason for this innovation was additional use energy. Risers and heated towel rails connected to the hot water supply system consume thermal energy, but this consumption was not previously taken into account in calculations of utility bills. Since heating fees can only be charged during the heating season, heating the air through the use of a heated towel rail was not paid for as a utility service. The government found a way out of this situation by dividing the tariff into two components.

Equipment

If the water heater fails, the bill will be hot water will not increase. In this case, authorized employees of the management organization are required to repair the equipment urgently. But since repairs require payment, residents must still pay this amount. Although the heating bill will remain the same, the cost of repairs and maintenance of the property will increase. This is explained by the fact that water heating devices are part of the property of homeowners.

As for non-standard situations, when, for example, some apartments in a multi-storey building have access to hot water, and the second only to cold water, issues regarding payment for heating are resolved on an individual basis. As practice shows, residents are often required to pay for common property that they do not use.

Thermal energy component

If the calculation of payment for cold water is quite simple (it is carried out on the basis of the established tariff), then not everyone understands what is included in the cost of such a service as heating.

The amount to pay for a service such as water heating is calculated taking into account the following components:

established tariff for thermal energy;
expenses required to maintain a centralized hot water supply system (from central heating points where water is heated);
cost of thermal energy loss in pipelines;
costs necessary to transport hot water.

Payment for utility services for hot water supply is calculated taking into account the volume of water used, which is measured in m3.

As a rule, the amount of required thermal energy is determined on the basis of general house values, which are shown by hot water meters and consumed thermal energy. The amount of energy used in each room is calculated by multiplying the used volume of water (determined by the meter) by the specific heat energy consumption. The energy volume is multiplied by the tariff. The resulting value is the amount required to pay for what is written on the receipt as “water heating”.

How to calculate it yourself in 2018-2019

Water heating is one of the most expensive utilities. This is explained by the fact that when heating it is necessary to use special equipment operating from the mains. To make sure that the receipt shows the correct amount to be paid, you can do the calculations yourself and compare the resulting value with the amount indicated on the receipt. To do this, you need to find out the amount of payment for thermal energy established by the regional tariff commission. Further calculations depend on the presence or absence of metering devices:

If you have a meter installed in your apartment, then you can calculate the consumption of thermal energy based on its indicator.
If there is no meter, calculations should be made based on established standard indicators (set by an energy-saving organization).

If there is a general heat energy consumption meter in a residential building and individual meters installed in the apartments, the calculation of the amount for heating is calculated based on the readings of the general meter and further proportional distribution for each apartment. If such a device is not available, the amount required to pay for heating is calculated based on the standard energy consumption for heating 1 m 3 of water in the reporting month and the readings of an individual water meter.

Where to write a complaint

If the legality of the additional line “water heating” in receipts is in question, in order not to overpay for heating, it is recommended to first contact the Criminal Code with a request to explain what this item means. Appearances new line in the receipt is legal only on the basis of the decision of the owner of the apartment building premises. In the absence of such a decision, you should write a complaint to the State Housing Inspectorate. After filing a complaint with the Criminal Code, you must be provided with an answer with explanations within thirty days. If you refuse to justify why such a service is indicated in the receipt, you should file a complaint with the prosecutor's office with a claim in court. In this case, if you have already paid the amount indicated in the receipt, the basis for the claim will be Article 395 of the Civil Code of the Russian Federation. If a refund is not required, but you must pay for services that are not provided to you, file a claim to exclude the “water heating” line. In this case, it is worth referring to Article 16 of the Law “On Protection of Consumer Rights”.

Every homeowner must know how to calculate hot water for subsequent payment. The fact is that the provision of this service occurs in quantitative terms, and if the hot water consumption is calculated incorrectly, this can result in a fairly large amount of overpayment or debt.

In addition, if, as a result of such an error, you do not pay for the hot water supplied to you on time, this may lead to its shutdown.

If you do not pay for the hot water supplied to you on time, this may lead to its shutdown

Payment for services for the supply of hot water to the population is regulated by Decree of the Government of the Russian Federation dated May 6, 2011 No. 354. According to it, it must include 2 components:

Providing hot water supply directly to residential or non-residential premises.
Providing hot water supply for general house needs or for the needs of a land plot, as well as ancillary buildings located on it.

Typically, centralized hot water supply systems are used in cities to supply such water to apartments, communal apartments and rooms in multi-apartment residential buildings. Tariffs for hot water are set by federal Service on tariffs, as well as its divisions in the regions, so if you don’t know how to calculate the tariff for hot water, you can go to the website of this body. In addition, your local resource supply organization can provide you with an example of such a calculation.

Tariffs for hot water are set by the Federal Tariff Service

In any case, it is worth knowing that the formula for calculating the cost of hot water includes not only the tariff itself, but also other indicators. For example, if your utility organization has established a two-rate tariff, then you will pay:

payment for the consumption of one cubic meter of hot water;
payment for the maintenance of the hot water supply system based on one gigocalorie.

With a one-component tariff, only consumed cubic meters are paid, which includes expenses for other needs. In addition, the approved methodology, which answers the question of how to calculate and how much a cube of hot water costs, also takes into account what category of consumers you belong to. This could be industry, public institutions or the population.

A common house hot water meter is used, which is installed on the basis of a decision of the general meeting of owners of residential premises

If for other categories of consumers all issues regarding utility payments are resolved by special employees on staff legal entity, then the population calculates and pays for hot water consumption independently. At the same time, he is also entrusted with the obligation to pay expenses for general household needs. For this purpose, a common house hot water meter is used, which is installed on the basis of a decision of the general meeting of owners of residential premises.

A separate scheme is used to calculate hot water supply if an individual boiler room is installed in the house. So, in the bills there is no line “hot water supply”, and instead of it there are 2 positions: water heating and cold water supply for hot water supply. This subtlety will need to be taken into account by all homeowners in such houses.

Payment for hot water for the population

according to the counter;
according to the general standard.

The first option is the most profitable for the owner of a residential premises, since it allows him to pay only for the volume of hot water that he actually consumed. At the same time, every month he will need to transfer meter readings to the local resource supply company. It is usually called “Vodokanal” or “Teploenergo” and is municipally owned.

Payment for hot water by meter

In the second case, you have to pay based on the general standard established by the Government, taking into account the number of residents registered in a particular living space. Typically, the standard is applied when the apartment does not have a meter installed or it is broken. At the same time, as a measure to encourage the population to install metering devices, the Government has been gradually increasing the standards by 1.6 times by 2017 since 2015.

As for specific figures, for 2016 in Moscow the standard for hot water consumption is 166 liters per day per person. In other regions it may be different. In any case, it will be more profitable to pay using a meter, so it makes sense to install it in the premises as early as possible.

Important! In addition to the standard and meter readings, the cost of hot water is also calculated taking into account the readings of a common house meter.

You can find out how to calculate one for hot water by contacting the company that provides management services for your apartment building. Generally speaking, apartment meter readings are subtracted from the readings of the general building meter, and the resulting balance is divided, based on a special formula, among all residents registered in the house.

Hot water payment receipts

It is also worth keeping in mind that modern technologies allow you to pay utility bills remotely or on a special schedule. This will be especially convenient if you leave your region of residence for some time or are very busy. To make payments according to the schedule, you will need to write a statement to your local bank branch about this or set it up accordingly Personal Area on your bank's website.

In any case, try to pay the cost of hot water in full and on time

Next, the required payment amounts will be withdrawn from your account in right time, which will allow you not to become a debtor for utility bills. In any case, try to pay the cost of hot water in full and on time.

Transmission of meter readings

As you already understood, the easiest way to calculate hot water consumption is to take readings from a meter installed in a residential area. This procedure must be done once a month. To do this, you will need to write off the first 5 digits of the readings from the meter.

Calculation of hot water consumption

Based on them, you can independently calculate your hot water consumption. To do this, subtract the new readings from last month’s readings. The difference you receive will be your monthly expense.

If you are wondering how to calculate hot water from a receipt, then you can do this by multiplying the readings obtained using a meter by the tariff in force in your region. This calculation may be useful to you when you have questions about the numbers indicated on the payment receipt. With complaints about this, you often contact the resource supply company, where you are required to recalculate the hot water you consumed.

Unscheduled water meter check

After you take the hot water meter readings, they will need to be transferred to the water supply organization. This can be done in several ways, for example:

using the website of such an organization or management company;
using special forms;
at the office of the organization that supplies you with burning water.

After transmitting the readings from your individual hot water meter, you will only have to wait for a receipt for payment to arrive. If you have figured out how to calculate hot water before this time, you can double-check the amount billed to you to avoid mistakes. At the same time, if several water meters are installed in your apartment, you will have to transmit readings from all of them.

By the way, you will need not only knowledge of how to calculate hot water, but also how to check the accuracy of the meter reading. To do this, record the readings of the three red numbers on its scale, after which approximately 30 liters of water are drained from the tap using a ten-liter bucket. If the meter shows a higher or lower number, this may be a sign that the water meter requires an unscheduled check.

Internet banking for paying for hot water

After an invoice is issued to you based on the testimony you provided, you can pay it in several ways, for example, at Russian Post, through Internet banking, and also using an ATM. If you delay payment for more than 3 months, you may be charged a penalty and your hot water may be turned off. After six months, utility companies will be able to go to court to evict you from the premises you occupy.