Reviews 

Installation of router d link. Configuring WiFi router D-Link dir300 ("gray" interface). Additional encryption options

So, you just bought a D-Link router, and how to quickly and correctly configure new router This article was written with Wi-Fi.

Setting up the router model:

DIR-140L, DIR-516, DIR-615/F, DIR-620, DIR-632, DIR-651, DIR-815/A, DIR-816/AC, DIR-822, DIR-825/AC, DIR- 857, DIR-879, DWR-921, DIR-300, DIR-615, DIR-615/GF, DIR-620/GA, DIR-640L, DIR-806A,

DIR-815/AC, DIR-816L, DIR-825/A, DIR-825/ACF, DIR-860L, DIR-890L, MTS DIR-320

In the box with your router you will find:

The router itself
Power adapter
Network cable
Wi-Fi configuration card (in older models this will be a CD)
Quick Installation Guide

Before you start

For users with DSL providers. If you are using PPPoE connection, you will need a username and PPPoE password. If you do not have this information, contact your service provider.

Internet (ISP). Do not proceed until you have this information.

For users with internet via modem, make sure you have disconnected the power from your modem. In some cases, you may need to turn it off for up to 5 minutes.

For users who have a modem or router provided to you by your ISP. You need to set it to "bridge" mode for your D-Link router to work properly.

So let's get started.

Quick Installation Instructions

Step 1: Connect the included power adapter to a power outlet and router

Step 2: Connect Ethernet cable to the WAN port. (WAN ports are usually yellow)

Step 3: Wait a moment until the indicator light comes on

Step 4: Take a Wi-Fi device, such as a phone.

Step 5: Browse network settings shown on the configuration card and connect to your Wi-Fi (SSID). The password is also indicated on the card.

Congratulations! Ready!

Step 6: Remove power from your cable or DSL internet modem

Step 7: Connect the Ethernet cable from your computer to the LAN port (port 1,2,3 or 4) on your router

Step 8: Connect your cable or DSL modem to your router's Internet port

Step 9: Plug in the router, as well as the DSL modem, if you have one.

Step 10: Open your internet browser and enter 192.168.0.1 into the address bar.

Step 11: You will be offered assistance from a wizard quick setup D-Link router, click "Next" to begin.

The indicator light on the front panel will blink and begin to reboot. The router itself will scan to determine the type of Internet you have. The Quick Setup Wizard will then automatically launch.

If, for some reason, the automatic scan did not detect your Internet type, you will be asked to select it manually:

Select your time zone.

Easy to install

Almost all D-Link solutions are easy to configure and install. An ordinary consumer who is not very familiar with computer or telecommunications equipment is quite capable of understanding them. It is also worth noting that D-Link devices are supplied with detailed instructions, which greatly facilitates their connection.

Anyone can install D Link on their own!

Thus, in order to add any D-Link device to your home, you do not need to seek the help of specialists at all. To install D Link correctly, follow a strict sequence of steps and carefully monitor what you connect and where.

So, to start connecting D Link, turn off your computer as well. Then you need to connect the antennas included in the D Link kit to its rear panel. If you connect your modem using a regular Ethernet cable, disconnect that too. If you use a DSL modem or cable modem to access the Internet, you do not need to disconnect the cable. Just disconnect it from the computer.

Next, you need to connect one end of the Ethernet cable to one of the D Link ports, and the other to the computer's Ethernet adapter. After that, turn on the power of the D Link and wait a few seconds until its indicators light up.

Installing D Link correctly is easy

As soon as the lights flash, connect the D Link power cable (always included as standard) to the 15VDC port on the rear panel. Plug the D Link power supply into a nearby outlet. After this, you can turn on your computer.

To install D Link yourself, launch your Internet browser. In the special line where you need to enter the address, enter the numbers 192.168.2.1. Then press the Enter button on your keyboard. This will give you access to the D Link configuration pages. Click on the Start button, which automatically launches the Internet Connection Setup Wizard. This program will immediately find the connection on its own. If this does not happen, carefully check whether the D Link power cable and the Ethernet cable are connected correctly. In addition, try clicking on the Detect Connection button. She should check that the D Link settings are correct. If after this you are unable to establish an Internet connection, you need to contact your provider and describe the situation that has arisen.

What is this Wi-fi for? This is the question that is probably the stupidest thing related to the Internet right now. It so happened that our computer and digital technologies are developing at incredible speed. For example, the most popular products now are: smartphones, tablets and laptops.

All of these devices, as a rule, already have a reception adapter installed WIFI signal, which allows you to use wireless Internet in all corners of your home. Some people just want to get rid of long and unnecessary cords throughout all the rooms, which in the future will simply fall under their feet. A Wi-Fi router that will distribute the Internet signal throughout the house will help us solve both situations.

But buying the router itself and unpacking it and putting it on a shelf is not all. You also need to connect a cable to the Internet and configure the device itself to receive and distribute the signal. Right now I will show you in detail how to set up a Dlink Dir 300 wifi router. If you have a different router, you can do everything in the same way, but if it’s a different one, it’s okay, setting up all routers is almost the same, there are only minor differences in the interface.

Next, I will tell you how to correctly connect and set the settings in the D-Link DIR-300 Wi-Fi router for distribution wireless internet, and also how to install the key on Wi-Fi network, which would protect your connection from freebie lovers.

Connecting the D-Link DIR-300 router

1. When you open the box you should find the following contents:

  • The Wi-Fi router itself;
  • Power cable;
  • 1.5 m patch cable;
  • Installation disk with drivers;
  • Manual;
  • Warranty card;

If this entire set is present, then take the router, a cord for connecting to the outlet and a patch cord, and move on to the next step.

2. So, you can place the device anywhere, as long as there is access to an outlet and the Internet cord can reach it. If you use a standard cable to connect, then, of course, you will have to place it near the computer. But, in the future, you can buy a long cable on the radio market, in specialized stores, or crimp the cable yourself for further movement around the house.

Let's first look at all the router connectors that are located on the back side:

  1. Button to reboot or reset the router settings;
  2. Power connector;
  3. Input for connecting an Internet cable;
  4. Four LAN ports for local connection computer.

A fully connected device should look like this: first, connect the power supply to the router, then to the port called “ Internet" (V On other routers it may be called WAN or be painted in some color different from the four LAN ports), we connect the Internet cable from the provider and finally plug the network cord that you found in the router package into any of the LAN ports, and the other side into the computer.

Everything is ready, the device is connected and ready for configuration.

Setting up WiFi router D-Link DIR-300

1. To start setting up D-Link router DIR-300, we need to go to its interface, for this we enter one of the following IP addresses 192.168.1.1 or 192.168.0.1 in any Internet browser. The router interface will open where to start the robots you need to enter the username and password, immediately try the standard ones: admin, admin. By pressing “Enter” its settings should open.

Network address and data according to standard account You can find it on a sticker located on one of the sides of the router or, read step by step instructions about how to get into its interface. If you've tried everything possible options spilled and you just can’t get into the settings menu, most likely you’ll have to return the router to the original settings.

2. At the very beginning let's change standard password“admin” to a more secure one so that no one can hack it. To do this, select “ System» –> « Administrator password" In the field with the user name, select “ admin" and indicate your preferred password. I recommend using passwords of more than 8 characters with capital letters and always numbers.

After entering the password, double-click on the “Save” button to change the standard password.

Setting up the Internet in the D-Link DIR-300 WiFi router

To set up the Internet in the D-Link DIR-300 router, you need to go to “ Net", and then " Compound" and here select the connection called " WAN", clicking on it with the left mouse button.

In the next window you need to check all the boxes as indicated below. In field " MAC» leave the MAC address set by default, if the company that provides you with Internet services uses MAC address binding, then Most likely you will have to copy the physical address of your computer into this field.

Setting up a Wi-Fi network and its security on the D-Link DIR-300 router

1. By going to the tab " WiFi"click on " basic settings" Here we give the name of the Wi-Fi network by writing it in the “ SSID» and indicate the region in which you are currently located.

To save the settings, click " Change».

So, in the field " Network authentication"select the next type of protection" WPA2-PSK" In line " PSK encryption key"Enter the password that will be used in the future when connecting to Wi-Fi. The recommendations are the same: use capital and small letters with numbers. In the WPA encryption settings, specify the following type “TKIP”.

Again, to save, click “ Change».

Completing the setup of the D-Link DIR-300 Wi-Fi router

Having saved all the parameters, we will need to do this again and restart the router. Moving to the upper right corner, point to the word “ System"In the drop-down window, select "".

By rebooting the device, you can say with confidence that the setup of the D-Link DIR-300 home router is complete. As you can see, there is nothing complicated and I’m just sure that you can easily cope with it. I’ll tell you even more that the technicians who come to the call to configure the router do all the same actions that I described above. So, read everything carefully and you will be able to save money on calling a specialist.

How to set up a WiFi router D-Link dir 300

The first thing that owners of a newly purchased D-Link DIR-300 router are interested in immediately after connecting it is the issues of setting up a wireless wifi network. After all, this is why you buy the device. A wifi network is quite enough to provide Internet access to all gadgets in the apartment. If previously households had conflicts over access to the Internet, then with the purchase of the D-Link DIR-300 all their worries will melt away like smoke. But this will happen only after we correctly configure the D-Link DIR-300 wireless network wifi In addition to setting up this service, the router also supports other communication technologies, such as VPN. The admin panel of the router has options corresponding to them. But we will not touch on these issues here. We are only interested in wifi!

Like other settings of the D-Link DIR-300 router, wireless network settings are carried out via the web interface. You can access it from a browser on the computer to which the device is directly connected. We will consistently describe all the steps necessary to organize full support for a wireless network in a confined space in your home. Read carefully and repeat after us.

Assigning a network name

Our first wifi setup on the D-Link DIR-300 router will be to assign a network name. To begin, let's do the following:

  • In the menu on the left, select “Wi-Fi” -> "General settings"..
  • In the panel on the right, check the box "Enable wireless connection.".
  • Set the “MBSSID” option to “Disabled”. .

Let's move on to actually setting up the router's network name. For this:

  • Go to the “Wi-Fi” menu -> "General settings"..
  • In the “SSID” field, enter the name of the future D-Link networks DIR-300. It should be typed in the Latin alphabet - no Russian letters! By this name you will search for a network among others.
  • Field "Channel".- \ assign the “Auto” mode. . This parameter is usually adjusted when communication interference occurs. If wifi is not working very well, then try playing with this value.
  • Field " Wireless mode"set to the value "B/G/N Mixed". . If you work with a laptop or use a smartphone, you can set the value “G Only” here - this will allow the system to work at the limit of its capabilities.

Assigning access rights

Routers like the D-Link DIR-300 provide a signal not only within your home, but also a little further away. If you live in an apartment building, then the signal from your device will reach neighboring apartments, and maybe spread further.

If there are particularly cunning people among your neighbors, they can easily steal your traffic. In this case, the speed of your Internet connection will decrease as much as your neighbor’s increases.

Distributing traffic to family members is one thing, but sharing it with strangers and not very decent people is quite another. Therefore, the next Wifi setup on the D-Link DIR-300 that we will do will concern restricting access to your router from outsiders. Only those who know the password will be able to connect to the system.

We sequentially perform the following manipulations:

  • We launch the browser on the computer and enter the IP address of our device into the address bar: http://192.168.0.1.
  • In the menu on the left, select “Wi-Fi” -> "Security Settings"..
  • "Network authentication" set to “WPA-PSK/WPA-2-PSK mixed”. .
  • Enter any desired password in the field "PSK encryption key.". Do not assign a password that is too primitive, like “123” - such wifi can easily be hacked.

Here, in fact, are all the minimum settings required to organize a wireless network based on the D-Link DIR-300 router. If something doesn't work, then the reason lies somewhere outside the basic settings. We will look at some problems of this kind for the D-Link DIR-300 router below.

I plan to write a number of different articles on routers from the D-Link company, and in almost every article you need to write how to go into the settings of your D-Link in order to configure some function, change the password, etc. I recently wrote, So I had to fully describe the process of logging into the control panel. Therefore, I decided to prepare a detailed article on how to enter settings on D-Link routers. And in other articles I will simply put a link to this article :) I already wrote (for all manufacturers), and specifically. I will try to prepare such instructions for each router manufacturer.

With D-Link, the settings are very simple. Like most manufacturers. And if you used to have Asus, or for example Tp-Link, then you should not have problems accessing the control panel on D-Link. I already wrote in some article that I just don’t like the fact that D-Link’s settings seem to change with almost every firmware update. By the way, how to update it, I already. Well, okay, their routers are good, popular, you don’t have to pay attention to this, it’s just difficult to prepare instructions. I will prepare this article using the example of the D-Link DIR-615 router (with firmware 2.5.20).

Entering D-Link settings

As usual, we first need to connect our router to the device from which we will enter the settings. This could be a desktop computer, laptop, tablet, phone, and even a TV. But, if possible, it is best to configure the router according to network cable, that is, use a desktop PC or laptop for this matter. But, if this is not possible, then you can configure it via Wi-Fi from the same laptop or mobile device.

Connection via network cable

The cable must be included with the router. We take it and connect the router to the computer. Like this:

On the router, connect the cable to one of the 4 LAN connectors. On a computer or laptop, into the network connector. There shouldn't be any problems here.

Wi-Fi connection to enter settings

If you want to configure your router from a device that cannot be connected via cable (or you don't have cable), then you can connect via Wi-Fi. If you have already used a router, then you know how to do this. If the router is new and you want to configure it, then immediately after connecting power to it, it will broadcast the wireless network. The name of which will be standard. And as far as I understand, it is the same as the model of your router. For example, with the D-Link DIR-615, the default Wi-Fi network is called “DIR-615”.

Find the network on your device and select it. For example, on a laptop (I wrote about connecting laptops to Wi-Fi):

The default network may be without a password (in this case, there will be a corresponding icon next to it, and the password request will not appear). But, even on a new router, when all the settings on it are by default, the network can be protected. The standard password is indicated at the bottom of the router and is signed as WPS PIN.

If you are asked for a password when connecting, please provide it. The connection to the router must be established.

Go to the control panel at 192.168.0.1

The most important point: all the standard data for entering the settings are indicated on a sticker on the router itself.

The IP address for accessing the settings is indicated there, for D-Link it is 192.168.0.1 . Username - admin, and the standard password is admin.

Open any browser and type our IP in the address bar - 192.168.0.1 . Let's go through it.

You will be prompted for your username and password. The user name is admin and the password is also admin. But, provided that you have not changed it yet. If you changed it, please indicate the one you installed. And if you forgot it, you will have to reset the settings (press the RESET button on the router for 10 seconds with something sharp).

The router control panel will open, and a window will immediately appear in which you need to specify twice New Password, which will later be used to enter settings (instead of admin). Specify it and click the button Ready.

Save your settings. Click on the menu item System(top) and select Save.

That's all, you can continue setting up your router. Just don’t forget to save the settings, and when you’re done, reboot the router (turn off and on power).